@Ruler of COM The docs+ for the COM-HPC Server Base Carrier - more specificly the pinout for frontpanel is incorrect.It differs from the module manual as well.And so is also the brochure that is at...
Posts made by David Robertsson
-
Suggestions for documentation improvements/changes?posted in General
-
i2c - freebsd tinkeringposted in Hardware
@Anson ooh, you are?Been following some related work on the freebsd project site and they seem to have something going for the i2c controller. I breifly tested the FreeBSD current branch and it see...
-
Not getting any SOL output from host when running "ipmitool... sol activate"posted in Software
@Rebecca Cran I just assumed it didnt work, noticed it in service config, but there is no way of selecting interface or setting network port to it.
-
i2c - freebsd tinkeringposted in Hardware
Hi!Noticed in the datasheet that there are some i2c-busses available.Am I on a goose chase thinking that I should be able to interface the i2c bus?Where can I read more about the hardware details/s...
-
Dead device - No BIOS - IPMI works. -- Resolvedposted in Hardware
@Anson Thank you for the 100% support!and again thanks to @Willy Tarreau for chipping in as well.Hopefully this thread will be helpful if others experience similar issues in the future DRAM popul...
-
Dead device - No BIOS - IPMI works. -- Resolvedposted in Hardware
@Willy Tarreau and @Anson Thank you both for all the input and help!As it seems, the CPU hasnt been mounted correctly on my rigg. As Im missing a correct torque tool - I did some tickling of ...
-
Dead device - No BIOS - IPMI works. -- Resolvedposted in Hardware
@Willy Tarreau Well, connecting them seperately on MC[0] or MC[1] works absolutely fine.Sounds very weird, that none will work on MC[2|4|5|7] because of a spec problem.. A spec problem for a DIMM l...
-
Dead device - No BIOS - IPMI works. -- Resolvedposted in Hardware
@Anson Hello and thank you plenty Anson!I have started the hunt for a tool that can assist me with checking the torque of the screws. I proceed to the other steps until I have such tools in my hand...
-
Dead device - No BIOS - IPMI works. -- Resolvedposted in Hardware
@Anson Ruan Hi!Thanks for the information!Latest update.I got 6 new fresh RAM-sticks. All of the recommended type and model from the AVL.The system now boots, but it fails to use all six of the ins...
-
Dead device - No BIOS - IPMI works. -- Resolvedposted in Hardware
@Anson Ruan Thanks for the clarification!I found a supplier that is able to send me new sticks on short notice, So will probably/hopefully recieve six new sticks of the confirmed 64gb modules today...
-
Dead device - No BIOS - IPMI works. -- Resolvedposted in Hardware
I have now tested to move one stick around.Still getting the same error. ERROR: MC[X]: 00f100b4 where X is changing to the current slot of the DIMM.I assume I might of been in bad luc...
-
Dead device - No BIOS - IPMI works. -- Resolvedposted in Hardware
@Anson Ruan Hello! Thanks for your reply.Im not sure what 9 star shaped screws you are talking about. The screws connecting the cpu-module to the carrier board is only 8? (I assume they a...
-
Dead device - No BIOS - IPMI works. -- Resolvedposted in Hardware
@Anson Ruan thanks for the quick reply! NOTICE: DRAM FW version 211207 CP: 0ff00900 MEMC param: mcu_enable_mask = 00000011 [default: 000000ff] MCU param: ecc_en = 00000002 [default: 0000...
-
Dead device - No BIOS - IPMI works. -- Resolvedposted in Hardware
Hello you all!My gear just arrived, so I started hooking everything up.When I plug in power - My led3 indicator gives me "82" - as push power btn, the led changes to "FF".I get no BIOS promt, but I...
Search
Forum statistics
- Page views (24h):
- 68
- Page views (30d):
- 2,511
- Topics:
- 196
- Posts:
- 745
- Members:
- 185
Newest members
Most liked authors
-
O. JUD
14 -
Rebecca Cran
11 -
Jiaheng Wang
10
