@Rebecca Cran I'm confused, the image from November I found in the download section for AADK is a 2.04.100 while I'm on 2.09.100. Maybe there's a different download link that I didn't find ? Thanks!

@Rebecca Cran Hi Rebecca!  Much appreciated, thank you. I'm willing to give it a try. Unfortunately the machine is refusing to boot again for an unknown reason ("synchronous exception at xxx"...

Hi Rebecca,  MMC on module connect to the SMPro through pre-defined I2C bus. leverage it from Ampere Altra's reference design. it is capable of reading information.  for example, by usi...

Yes that would work if you flash the SPI flash on the module through DB40 connector with a Dediprog.  However if you would like to have a backup / recovery on the carrier SPI flash, that is p...

@Ruler of COM The 13MB version can also be burned via an eeprom programmer by specifying the offset to flash it at. e.g.   dpcmd --spi-clk 0 -v -a 0x400000 -u edk2_fw.bin

@Ruler of COM You already have EDK2 v2.04.100.11 on LVFS: https://fwupd.org/lvfs/devices/com.adlinktech.COM-HPC-ALT-CC.firmware

Rebecca we took it down for a couple of days because we found a small issue when updating to this version while BMC is not latest version 2.06. Not critical but we are modyfying the README to adivs...

I noticed the Github repository at https://github.com/ADLINK/edk2_aadp/ no longer exists. I was wondering why it's been removed or the permissions changed so we can no longer access it.

I've been working on porting OpenBMC to the ADLINK Ampere Altra Dev Kit, and from reading the Ampere Altra BMC Interface document it looks like I should be able to use the smpro-hwmon driver to rea...

Replacing that 60mm rear fan by two stronger ones (effectively quadruplung air throughput there) helped a bit. With those, I now get the open-case temperatures now also with a closed case. But I a...

I think Redfish support on MegaRAC is a licensed feature you have to buy.

Hi Jiaheng,  the carrier board jumper setting is correct. we are investigating this feature and will give update. thanks 

For the CPU temperature issue, the BMC would need to be built with the Linux smpro-core and hwmon-smpro drivers. https://docs.kernel.org/hwmon/smpro-hwmon.html  

Thermal paste vs. pad doesn't make much of a difference for me. With the case closed, the CPU temperatur goes to 105°C. IMO, the current CPU cooler is not very well suited for a rack case: It...

Peter,  Looking at the partnumber you provided this is a SATA drive, note that you need NVMe storage  Sadly SATA is on it's way out in most of the arm based SOC's     

@Will 💜 I have it reading data from the FRU and showing the system information (mfg, serial number etc.) but so far adding sensors for fan monitoring/control, voltages etc. has eluded me. I have th...

@Rebecca Cran What's the status of your OpenBMC port, out of curiosity? Is the basic functionality working or is there much more yet to do?

@Willy Tarreau You might want to upgrade to the firmware that ADLINK just released, since at least on my system it boots _much_ faster since SSIF is now working.

@Olof Johansson ADLINK have just released updated BMC, MMC and EDK2 firmware which has several very nice improvements. SSIF support is added and works in both EDK2 and Linux, the MMC now properly s...

@Master of SMARC  We connect a M.2 SSD to connect B, but we have not got any messages from linux kernel. The SSD we use is Transcend  TS1TMTS430S, it is a M.2 2242 SSD.  https://t...