I don't use HYDIS screen but an AUO G150XAN02.2 .  I will have a look in the HYDIS dts and I think I have to adapt it. Can you point me on all elements in the dtb that enable HYDIS lvds scre...

Dear @O. JUD, By default, our image can support the following LVDS panel(HYDIS HV150UX2-100 18 dual panels). Don't need to change anything in the dtb. we recommend the following steps to set up the...

Hi,  Does the LVDS should work without change in the dtb .  I plugged an LVDS screen on dev board and i have nothing on screen .  Same after have enable lvds-channel@0 and lvds-ch...

Dear @Jared Horton, we found the problem. This was caused by a compatibility issue with the IMX8M Plus board. It is necessary to use an SSD type that supports NVMe SSD M.2 B key. As part of our val...

Hi @O. JUD, our image won't support this future. For more details, you can refer to the NXP official website.

Hi,    Is it possible to have an  rs480 port with SER2 pin on the 40-PIN Conector ?  SER 2 RX 7 8 SER2RTS# SER 2 TX 9 10 SER2 CTS# Rgds 

@Kothandaraman Kannadasan  yes I tried the Image and dtb files of core-image-minimal from this branch and it works. I will rebuild my image from adlink-lec-imx8mp-yocto-hardknott_1v5.xml th...

Dear @Kothandaraman Kannadasan , yes I tried the Image and dtb of core-image-minimal from this branch and it works. I will rebuild my image from adlink-lec-imx8mp-yocto-hardknott_1v5.xml thanks

Hi,  cog works now The problem is solved by replacing :  PACKAGECONFIG_pn-cog = "fdo" by  PACKAGECONFIG_pn-cog = "wl"

Dear @O. JUD, Please use the following command while building the image. repo init -u https://github.com/ADLINK/adlink-manifest -b lec-imx-yocto-hardknott -m adlink-lec-imx8mp-yocto-hardknott_1v5.xml

For your information.  cog does not run on wayland as expected .  i have opened a case on this topic here : https://github.com/Igalia/meta-webkit/issues/431 Rgds

Good to know. Thanks

@Kothandaraman Kannadasan , I followed the steps discribed in the link your provide .  Except that i used the Hardknott branch with the command :  repo init -u https://github.com/ADLI...

Dear @Mark Abrams, I apologize for the inconvenience. The mail had been sent to the wrong address. The mail has been forwarded to you just now. The subject of the mail is "FW: [I-Pi SMARC's Forum] ...

Dear @Jared Horton, Our I-Pi SMARC IMX8M Plus board doesn't have the BIOS settings.

hi, as part of some custom requirements, we need to know the ECCN of the products we order Are they documented here somewhere? Could you share them so when we go vi the checkout page we can note t...

Dear @O. JUD, Here is the link for building the Yocto image for our I-Pi SMARC IMX8M Plus product, it has all the packages and drivers you need. https://www.ipi.wiki/pages/imx8mp-docs?page=HowToBu...

Dear @Sven Brandau, Sorry for the inconvenience. A kernel upgrades from Zeus to Kirkstone is currently underway. Additionally, it is a time-consuming process. The software will be available for all...

Hi  For me the device driver is build in the kernel not as the module furthermore i cannot find any package called *wm8960*  in my build folder. Are you sure it is provided as a module ?...

@Kothandaraman Kannadasan I also tried to set the dip switches to the recovery setting and then I powered on the board but BIOS settings never showed up. All I saw was a blank black screen. I assum...