Hello Rebecca, any news about your firmware update ? Today I found my machine at 1.0 GHz, voiding all my testings, that's particularly annoying :-( Thanks!
Hello Rebecca, any news about your firmware update ? Today I found my machine at 1.0 GHz, voiding all my testings, that's particularly annoying :-( Thanks!
@Jiaheng Wang maybe you're facing the same problem as I am in this thread: https://www.ipi.wiki/community/forum/topic/100157/cpu-frequency-capped-to-23-ghz-instead-of-26-ghz Here it's a Q8...
Dear @Olof Johansson, The development not only belongs to EDKII. We plan to release EDKII, BMC, and MMC as well. The official public release of all the firmware is expected in December.
There's some exciting developent in the ADLINK Github repos for AADK/AADP, including plumbing up the glaringly missing SSIF interface support. What's the release roadmap for a firmware upd...
https://www.coolserver.com.cn/en/product_view_442_313.html But I'm still waiting for this product, the manufacturer said it is out of stock for a long time.
While I'm waiting for my Ampere Altra dev kit to arrive: The CPU cooler looks small. How well does it work for you? How loud is the fan? Are there any non-water alternatives? Are there any compat...
@Tu Ken Hi, I have successfully replaced my original Q32-17 to Q80-30, but after my replacement , the Q80-30 cpu can only run on 2.3GHz frequency. How to let it run in max frequency? &nb...
@Tu Ken Hi, here's my module's serial: 2371100KZV
Dear @Alee Kin, Unfortunately, there is no other method except the QFIL.
Hi, Is there any way to enter fastboot mode if adb is not work? Like "Press specific button" + "Connect adapter" or any? *The alternative method will be EDL and update image by QFIL. Best,Alee
@Anson Ruan I also need access to the images. In addition, I need the recovery procedure and images to recover my board in EDL mode since I have bricked it while trying 69board images. Regards, &...
Hi @peter zhang, Sadly, we cannot duplicate what you did. You can, however, refer to the solution from here. It might be helpful to you. https://askubuntu.com/questions/210177/serial-port-terminal...
hi @Kothandaraman Kannadasan i have try the cmd,but encounter the same error either best regards;
Dear @peter zhang, Type the following commands in the terminal, $ echo 'SUBSYSTEM=="usb", ATTR{idVendor}=="0e8d", ATTR{idProduct}=="201c", MODE="0660", $ GROUP="plugdev"' | sudo tee -a /etc/udev/...
hello: i follow the document:https://www.ipi.wiki/pages/1200-docs?page=AIoTToolInstallation.html#AIoTToolInstallation.html but encounter the...
Hi Jiaheng, Sorry for USB4, 5 and USB6, 7 aren't supported on the COM-HPC-ALT(Ampere Altra) and only USB0, 1 and USB2, 3 on the rear are workable, cause the carrier are desinged as maxnimu...
Hi Rebecca, As the current FAN_0 does not have a PWM signal due to an optional BOM on the module board, and only the module's BFAN_1 is activated in previous. The new BOM will activate bo...
Hi Ian, Rebecca, As the current FAN_0 does not have a PWM signal due to an optional BOM on the module board, and only the module's BFAN_1 is activated in previous. The new BOM will activa...
I connected the 9-pin Header to the Front panel of my chassis. But when I connected the usb device to the port, It has 5V power, but no usb signal. Cannot see the device in system. How to make USB4...
Hi,i want to know how to flash ubuntu 22.04 into ippi smarc 1200, anyone can help me?thanks!